Opel Vectra A

since 1988-1995 of release

Repair and car operation

Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions

10.13. Generator brushes

THE DELCO-REMY GENERATOR (EXCEPT SMALL-SIZED)

Removal

Removal of a forward cover of the DELCO-REMY generator

Arrangement of contact rings of a rotor on the DELCO-REMY generator

DELCO-REMY generator

And – nuts of fastening of wires of a winding of a stator;
In – screws of fastening of a shchetkoderzhatel/regulator of tension

PERFORMANCE ORDER

1. Remove the generator.

2. Using a chertilka, note the mutual provision of forward and back covers of the generator.

3. Unscrew three coupling bolts and remove a forward cover and a rotor from a back cover (see fig. Removal of a forward cover of the DELCO-REMY generator).

4. Check a condition of contact rings of the generator and, if necessary, smooth out them a small emery paper (see fig. An arrangement of contact rings of a rotor on the DELCO-REMY generator).

5. Unscrew three nuts, fixing wires of a winding of a stator to the rectifier block, and remove a stator (see fig. DELCO-REMY generator).

6. Unscrew the screw and remove the block of rectifiers.

7. Unscrew two screws and remove from a back cover щеткодержатель / a tension regulator. Note an arrangement of isolating washers under heads of screws.

8. Check smoothness of moving of brushes in directing and measure a dyne of brushes.

9. For replacement of brushes отпаяйте contacts of old brushes from a shchetkoderzhatel and on their place solder the new.

10. Check smoothness of moving of brushes in the directing.

Installation

Drill extraction for release of brushes of the DELCO-REMY generator

PERFORMANCE ORDER

1. Before installation of shchetkoderzhatel fix brushes in the wrung-out situation, using a steel wire or a drill.

2. Establish shchetkoderzhatel so that the wire or a drill came out through an opening in a back cover of the generator. Fix a shchetkoderzhatel screws.

3. Establish the vypryamitelny block and a stator winding in a back cover and fix nuts and the screw.

4. Establish a rotor in a back cover of the generator, then, according to earlier put labels establish a forward cover. Screw in three coupling bolts.

5. Take a wire or a drill from an opening in a back cover, thus brushes will fall by contact rings of a rotor (see fig. Drill extraction for release of brushes of the DELCO-REMY generator).

6. Establish the generator.