Opel Vectra A

since 1988-1995 of release

Repair and car operation

Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions

10.14. BOSCH generator

GENERAL INFORMATION

Measurement of length of brushes of the BOSCH generator

Removal

Unscrewing of screws of fastening of a shchetkoderzhatel / regulator of tension

Removal of a shchetkoderzhatel / regulator of tension from the BOSCH generator

PERFORMANCE ORDER

1. For improvement of access disconnect the main air branch pipe from the air filter, the air chamber or the throttle case.

2. Remove a weight wire from the accumulator.

3. For improvement of access it is recommended to remove the generator.

4. Unscrew two screws and remove щеткодержатель / a tension regulator (see fig. Unscrewing of screws of fastening щеткодержателя / tension regulator, Removal of a shchetkoderzhatel/regulator of tension from the BOSCH generator).

5. Check smoothness of moving of brushes in directing and measure length of brushes.

6. Otpayayte wires of brushes from a shchetkoderzhatel also remove brushes.

Installation

Arrangement of contact rings of the BOSCH generator

PERFORMANCE ORDER

1. At installation of new brushes it is also necessary to establish and new springs.

2. Establish new springs in направля yushchy a shchetkoderzhatel, then insert new brushes and check smoothness of their moving. If brushes move hardly or jam, using a small file, cut their lateral sides.

3. Solder wires of brushes to a shchetkoderzhatel. At the soldering watch, that solder was only in a place of the soldering and did not get on a twisted wire of a brush.

4. Check a condition of contact rings of the generator and if necessary, smooth out them a small emery paper (see fig. Arrangement of contact rings of the BOSCH generator).

5. Establish щеткодержатель / a regulator of tension and fix screws.

6. Establish the generator.

7. Connect a weight wire to the accumulator.

8. Establish the main air branch pipe.