Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   - 10.23. Repair of the distributor of ignition
      10.23.2. Models 16 SV
      10.23.3. DOHC models
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


d476fba5


10.23.2. Models 16 SV

Dismantling

Extraction of the cylindrical pin, drive of a shaft of the distributor fixing the plug on model of 1,6 l (BOSCH distributor)

Removal of washers from a shaft of the distributor of ignition

Removal of washers from a shaft of the distributor of ignition on model of 1,6 l (BOSCH distributor)

Extraction of a clamp of the electric socket (LUæAS distributor)

Detachment from a back part of the socket of the small socket on models of 1,6 l (LUæAS distributor)

Unscrewing of screws of fastening of a basic plate

Extraction of a basic plate from the case of the distributor of ignition on model of 1,6 l (LUæAS distributor)

Arrangement of the screw of fastening of a basic plate on model of 1,6 l (LUæAS distributor)

PERFORMANCE ORDER
1. Using a hammer and a drift, beat out the cylindrical pin, fixing the drive plug to a distributor shaft (see fig. Extraction of the cylindrical pin, a drive of a shaft of the distributor fixing the plug on model of 1,6 l (BOSCH distributor)).
2. Remove from a shaft of the distributor of ignition the drive and washer plug (see fig. Removal of washers from a shaft of the distributor of ignition).
3. Take a distributor shaft together with the cylindrical screen with teeths from the case of the distributor and remove washers from a shaft (see fig. Removal of washers from a shaft of the distributor of ignition on model of 1,6 l (BOSCH distributor)).
4. On the LUСAS distributor remove a spring clamp of the electric socket, then take the socket from the case of the distributor of ignition and from a reverse side of the socket disconnect the small electric socket (see fig. Extraction of a clamp of the electric socket (LUæAS distributor), the Detachment from a back part of the socket of the small socket on models of 1,6 l (LUæAS distributor)).
5. Unscrew screws and take from the distributor case a basic plate (see fig. Unscrewing of screws of fastening of a basic plate, Extraction of a basic plate from the case of the distributor of ignition on model of 1,6 l (LUæAS distributor), the Arrangement of the screw of fastening of a basic plate on model of 1,6 l (LUæAS distributor)).

Check

PERFORMANCE ORDER
1. Check a condition of a cover of the distributor of ignition on existence of corrosion of contacts, black paths between contacts, and also integrity and smoothness of moving of coal contact in the cover center. In the presence of defects replace a cover of the distributor of ignition.
2. Check a condition and fastening of metal contact of a rotor of the distributor. If contact scorched or weakened its fastening, replace a distributor rotor. At existence, remove from contact a deposit and corrosion traces, using a small file.
3. Check a condition of a sealing ring in a back part of the distributor of ignition and, if necessary, replace it.

Assembly

PERFORMANCE ORDER
1. Assembly is made in sequence, return dismantling. At assembly correctly establish washers. The plug of a drive establish so that the ledge of the plug entered into a groove in the top part of a shaft of the distributor.
2. Establish the ignition distributor, then check and, if necessary, adjust a corner of an advancing of ignition.