Opel Vectra A

since 1988-1995 of release

Repair and car operation

Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions

2.16. Forward sealing ring of a camshaft

Removal

PERFORMANCE ORDER

1. Replacement of a forward sealing ring of a camshaft can be made on the engine established in the car after removal of a pulley of a camshaft.

2. Remove a gear belt and a camshaft pulley.

3. Drill in a sealing ring two small openings located in the opposite ends of consolidation. Screw in two self-cutting screws in the drilled openings of a sealing ring and, using flat-nose pliers, extend for heads of screws a sealing ring.

Installation

PERFORMANCE ORDER

1. Clear a nest of a sealing ring.

2. Grease working edges of a new sealing ring with pure engine oil and, using a tubular opravka of the corresponding diameter, establish a sealing ring into place. At installation of a sealing ring do not damage working edges.

3. Establish a pulley of a camshaft and a gear belt. Adjust a tension of a gear belt.