Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   - 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
      2.19.2. Preparation for installation
      2.19.3. Installation
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


d476fba5


2.19.2. Preparation for installation

GENERAL INFORMATION

Interfaced surfaces of a head and the block of cylinders should be absolutely pure. For their cleaning use a firm plastic or wooden scraper. When cleaning be careful, as the aluminum alloy is very easy for damaging.

PERFORMANCE ORDER
1. Check that the deposit did not get to oil and water canals. It is especially important for greasing system as the deposit can block supply of oil to engine components. If necessary clear channels.
2. Check interfaced surfaces of a head and the block of cylinders on existence of notches, deep scratches and other damages. If defects small, they can be removed with machining. But at major defects of a detail are subject to replacement.
3. Using a metal ruler and щуп, check planeness of interfaced surfaces.
4. Clear openings under bolts in the block. Bolt screwing up in the opening filled with oil can break off the block because of hydraulic pressure.
5. Replace bolts of fastening of a head of the block of cylinders irrespective of their condition.