Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
2.2. General information
2.3. System of ventilation of a case
2.4. Compression check
2.5. Repair operations on the engine established in the car
2.6. The repair operations demanding removal of the engine
2.7. Recommendations about engine removal
+ 2.8. Removal and engine installation without a transmission
+ 2.9. Removal and engine installation together with a transmission
2.10. Replacement of support of the engine and transmission
2.11. Engine repair
+ 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
2.16. Forward sealing ring of a camshaft
2.17. Back sealing ring of a camshaft
2.18. Camshaft and camshaft case
+ 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
2.20. Removal and installation of a head of the block of cylinders on the removed engine
+ 2.21. Repair of a head of the block of cylinders
2.22. Cleaning and survey of a head of the block of cylinders
2.23. Hydraulic pushers of valves
2.24. Flywheel
2.25. Replacement of a forward sealing ring of a cranked shaft
2.26. Replacement of a back sealing ring of a cranked shaft
2.27. Oil pallet
2.28. Oil pump
2.29. Repair of the oil pump
2.30. Removal and installation of pistons and rods
2.31. Check of pistons and rods
+ 2.32. Removal and installation of a cranked shaft
2.33. Check of a cranked shaft
2.34. Survey and gap check in radical and shatunny bearings
2.35. Check of a working gap of the bearing
2.36. Check of the block of cylinders of the engine
2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
2.2. General information
The engine with four cylinders, established cross-section in a forward part of the car. Coupling and a transmission are located on the left side of the engine.
The block of cylinders is made of an aluminum alloy. The cranked shaft leans on 5 main bearings. Persistent half rings are established on the third radical bearing.
In the bottom heads of a rod loose leaves are established. Pistons fasten to rods piston fingers. Pistons from an aluminum alloy also have three piston rings, two sealing and one maslosjemny.
The camshaft located in the top part of a head of the block of cylinders, puts in action a gear belt of a drive and operates valves through the hydraulic pushers located under cams of a camshaft.
Greasing of the engine is made under the pressure created by the oil pump. Oil is sucked in via the mesh filter located in a maslopriyemnik and then arrives via the external established filter to canals of the block of the cylinder. From there oil arrives to коленчато му to a shaft and a camshaft. Bearings of the bottom head of a rod are supplied with oil through internal drilling in a cranked shaft. To camshaft bearings oil also moves under pressure. Cams distribute a telny shaft and the valve are oiled sprayed, also as well as all other mobile details of the engine.