Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   - 2.9. Removal and engine installation together with a transmission
      2.9.1. Removal
      2.9.2. Separation of a transmission from the engine
      2.9.3. Connection of a transmission with the engine
      2.9.4. Installation
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


d476fba5


2.9.2. Separation of a transmission from the engine

PERFORMANCE ORDER
1. Establish the power unit on соответ stvuyushchy bars. Using kerosene or solvent and a rigid brush, clear the power unit of dirt.
2. Unscrew and remove a protective cover of a case of coupling.
3. Check that the engine and a transmission are reliably fixed, then unscrew bolts of fastening of a transmission to the engine.
4. Being careful, separate a transmission from the engine so that the weight of a transmission did not press an entrance shaft.
5. On models with an automatic transmission unscrew three bolts and remove a protective cover of coupling. Before unscrewing of bolts of fastening of the hydrotransformer, using chalk or a marker, note position of the hydrotransformer in relation to a drive plate.
Prevention

For removal and installation of the engine it is necessary to use the winch and the elevating device. If from an automatic transmission even the hydrotransformer partially acts in film considerable leakage of liquid can take place. For prevention of leakage of liquid, being careful, disconnect the engine from a transmission and press the hydrotransformer to a transmission. If there will be a need to remove a transmission from the car, fix the hydrotransformer, having screwed bolts on a coupling case metal strips.

Wrench for a bolt of fastening of a pulley turn a cranked shaft of the engine before emergence of the first bolt of fastening of the hydrotransformer. A screw-driver for a gear wreath fix a flywheel from a provorachivaniye and unscrew a bolt of fastening of the hydrotransformer. Similarly unscrew the remained bolts of fastening of the hydrotransformer.