Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
- 4. Repair of the diesel engine
   4.2. General information
   4.3. The repair which is not demanding removal of the engine
   4.4. Compression check
   4.5. Top dead point (VMT) of the piston of the first cylinder
   4.6. Cover of a head of the block of cylinders
   4.7. Pulley of a cranked shaft
   4.8. Casings of a gear belt
   4.9. Replacement of a gear belt
   4.10. Check and installation of phases of a gazoraspredeleniye
   - 4.11. Mechanism of a tension of a gear belt and pulleys
      4.11.1. Camshaft pulley
      4.11.2. Pulley of the fuel pump
      4.11.3. Pulley of a cranked shaft
      4.11.4. Pulley of the oil pump
      4.11.5. Tension mechanism
      4.11.6. Single pulley
   4.12. Replacement of a sealing ring of a camshaft
   4.13. Check and adjustment of gaps of valves
   4.14. Camshaft and pushers
   4.15. Head of the block of cylinders
   4.16. Oil pallet
   4.17. Oil pump
   4.18. Replacement of a sealing ring of the oil pump
   4.19. Oil radiator
   + 4.20. Pistons with rods
   4.21. Flywheel
   4.22. Replacement of sealing rings of a cranked shaft
   4.23. Replacement of support of the power unit
   4.24. Recommendations about engine removal
   4.25. Removal and engine installation
   4.26. Engine repair
   4.27. Engine start after major maintenance
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


d476fba5


4.11.2. Pulley of the fuel pump

Removal

Use of the special tool for fixing of a pulley of the fuel pump from a provorachivaniye when unscrewing a bolt of fastening of a pulley


Removal of a pulley from a shaft of the brake pump
After removal of a pulley from a shaft of the fuel pump remove a segment shponka.

PERFORMANCE ORDER
1. Remove a gear belt.
2. Using the special tool, fix a pulley of the fuel pump from a provorachivaniye (see fig. Use of the special tool for fixing of a pulley of the fuel pump from a provorachivaniye when unscrewing a bolt of fastening of a pulley).
3. Unscrew tightening a bolt of fixing of a pulley and unscrew a nut of fastening of a pulley of the fuel pump.
4. Remove a pulley from a shaft of the fuel pump (see fig. Removal of a pulley from a shaft of the brake pump).
Prevention

The pulley of the fuel pump is established on a cone therefore for its removal it is necessary to use a stripper.


Installation

PERFORMANCE ORDER
1. Establish a segment shponka in a groove of a shaft of the fuel pump and establish a pulley, having combined a groove on a pulley with a segment shponka.
2. Fix a pulley a nut, having tightened it the demanded moment, thus hold a pulley from a provorachivaniye the special tool.
3. Turn a pulley of the fuel pump in such situation that adjusting openings were combined and fix a tightening bolt.
4. Establish a gear belt.