Opel Vectra A

since 1988-1995 of release

Repair and car operation

Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. A fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit in temperature of air arriving in the engine
   7.7. The sensor of temperature of air arriving in the engine
   7.8. Pressure removal in fuel system
   7.9. The fuel filter on models with the fuel pump out of a fuel tank
   7.10. The fuel filter on models with the pump in a fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump established out of a fuel tank
   7.13. The fuel pump established in a fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a toplivozalivny mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of a fuel mix on idling turns
   7.21. Regulator of pressure of fuel
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Measuring instrument of a stream of air
   7.26. Measuring instrument of weight of a stream of air
   7.27. Tape measuring instrument of weight of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step-by-step engine of management of supply of air (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor detonations (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions

7.35. Electronic control device (ECU)

Removal

Removal of the electronic control device (ECU) of a control system by the engine

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. Remove the lateral panel of furnish in deepening for feet of the driver.

3. Release the clamps, fixing the ECU block, remove the block and disconnect from it the electric socket (see drawing).

4. The ECU block consists of two parts: the main unit of engine management and the programmed block of memory. It is not recommended to divide blocks independently. Determination of malfunctions of blocks is necessary for making at Opel service station with use of the special equipment. If at ignition inclusion from the ECU block noise, probably is audible, it is damaged because of unreliable connection of contacts between blocks.

Installation

PERFORMANCE ORDER

1. Installation is made in sequence, return to removal.

2. Check correctness and reliability of connection of the electric socket.