Opel Vectra A

since 1988-1995 of release

Repair and car operation

Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


10.4. Check of system of ignition



At work on ignition system it is necessary to be careful with the included ignition, as it is possible to receive blow a current from a high-voltage part of system of ignition. People with stimulators of warm activity are not recommended to check and make repair of system of ignition. Switch off ignition before disconnect niy or connection of any element of system of ignition or щупов the measuring device.

The main malfunctions of system of ignition are caused by easing or oxidation of contacts, or short circuit on mass of a high voltage because of pollution, humidity or damage of isolation of high-voltage wires. Before drawing a conclusion on malfunction of any element in ignition system, check a condition of wires or electric chains of system of ignition.

It is not recommended to check spark existence, holding a high-voltage wire at small distance from the engine as thus it is possible to receive blow an electric current or to put out of action the control unit ignition. Also it is not recommended to determine admissions of ignition by a method of consecutive removal of high-voltage wires from spark plugs.

The engine is not started

1. If at engine start the cranked shaft of the engine is not turned or turned very slowly, check a condition and a battery charging and a starter. Connect щупы the voltmeter to plugs of the accumulator and disconnect the central high-voltage wire from a cover of the distributor of ignition and connect it to weight. Include a starter no more than for 10 seconds, and measure tension on the accumulator. If at starter work tension becomes less, than 9,5 In, check an accumulator condition, a starter and charging system.
2. If at engine start the cranked shaft rotates with normal speed, using a stroboscope, check a high-voltage part of system of ignition. If at engine start the stroboscope blinks, means, the high voltage moves to spark plugs and it is necessary to check a condition of spark plugs. If the stroboscope does not blink, check the central high-voltage wire going from the coil of ignition to a cover of the distributor, coal contact and a distributor rotor.
3. If the spark is present, check a condition and operability of fuel system.
4. If the spark still did not appear, possibly, the block management of ignition is faulty and in this case it is necessary to address on service station of cars.

Ignition admissions

Unsystematic admissions of ignition can be caused by the weakened contacts or a rupture of a chain in a control system of ignition or in a chain of primary winding of the coil of ignition or damage of high-voltage wires.

1. Switch off ignition and check that contacts on electric sockets of system of ignition pure and without corrosion traces.
2. Check that the ignition coil, a cover of the distributor of ignition and high-voltage wires, pure and dry. Check a condition of electric wires of spark plugs. Then check a cover of the distributor of ignition, coal contact and a rotor of the distributor of ignition. Check of spark plugs can be made serial replacement of spark plugs by the new.
3. Constant admissions of ignition are caused, most likely, by defects in a cover of the distributor of ignition, the ignition coil, high-voltage wires or spark plugs. For check of giving of a high voltage to spark plugs it is possible to use a stroboscope.
4. Lack of tension only on one high-voltage wire testifies to damage of this wire or a cover of the distributor of ignition. If tension is present on all high-voltage wires, means, spark plugs are faulty.
5. At total absence of a high voltage check a secondary winding of the coil of ignition which can be damaged.
6. If at system of ignition there are malfunctions which it is impossible to eliminate independently, it is necessary to address on service station.