Opel Vectra A

since 1988-1995 of release

Repair and car operation

Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
- 15. Brake system
   15.2. General information
   15.3. Anti-blocking system of brakes (ABS)
   15.4. Pumping of hydraulic brake system
   + 15.5. Replacement of forward brake shoes
   15.6. Replacement of back brake shoes on disk brakes
   + 15.7. Replacement of back brake shoes on drum-type brakes
   15.8. Replacement of brake shoes of the hand brake on back disk brakes
   15.9. Support of a forward brake
   15.10. Support of a back disk brake
   15.11. Brake disk
   15.12. Forward brake disk
   15.13. A back brake disk on models with SOHC engines
   15.14. A back brake disk on models with DOHC engines
   15.15. Brake drum
   15.16. Back working brake cylinder
   15.17. Brake board of a back brake
   15.18. Protective casing of a forward brake disk
   15.19. Main brake cylinder
   15.20. Repair of the main brake cylinder (model without ABS)
   15.21. Vacuum amplifier of brakes
   15.22. Hydraulic ABS modulator
   15.23. The ABS sensors established on wheels
   15.24. ABS control unit
   15.25. ABS relay (only ABS-2E system)
   15.26. Valves of adjustment of pressure
   15.27. Brake pipelines and hoses
   15.28. Adjustment of the hand brake
   + 15.29. Cable of the hand brake
   15.30. Lever of the hand brake
   15.31. Brake pedal
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


15.10. Support of a back disk brake


Extraction of a bolt of fastening of a support on back disk brakes

Arm of the ABS sensor which also fastens bolts of fastening of a support on models with DOHC engines

1. At existence remove caps of wheels, then weaken bolts of fastening of back wheels. Lift a back part of the car and fix on supports. Remove back wheels.
2. Remove brake shoes.
3. For reduction of losses of brake liquid uncover a popolnitelny tank of brake system, close a tank mouth polyethylene and again screw a cover. It is necessary in order that the cover tightly closed a popolnitelny tank. Alternatively, using a clip, press the brake hose going to a support.
4. Unscrew the connecting coupling, a fixing brake tube to a back part of a support and disconnect a brake tube. Be careful and do not deform a brake tube. Close openings in a support and a brake tube suitable jams.
5. Unscrew two bolts and remove a support from a fixing element of a nave, thus keep in mind that on models with DOHC engines bolts of fastening of a support also fix an arm of the sensor of anti-blocking system (see fig. Extraction of a bolt of fastening of a support on back disk brakes, the Arm of the ABS sensor which also fastens bolts of fastening of a support on models with DOHC engines).


1. Being careful and security measures, clear a support of a brake dust and dirt.
2. Do not unscrew the bolts, fixing both parts of a support to each other. In this case there can be a loss of tightness and a support will leak.
3. Using a screw-driver edge as the lever, remove a bracket of fastening of a dustproof cover of the piston, then, being careful, remove a dustproof cover.
4. Using a clip, fix one of pistons in a support. Submitting air under low pressure through an opening for a brake hose, squeeze out the piston from a support. Be careful not to drop the piston as in this case most likely, it will be damaged.
5. Using wooden whetstone, close an opening in a support. Remove a clip fixing the piston in a support and, using the compressed air under low pressure, squeeze out the second piston from a support.
6. Using the plastic or wooden tool, being careful, take sealing rings from flutes in the support cylinder.
7. Check a condition of pistons and cylinders. In the presence of scratches, рисок, wear or dot corrosion it is necessary to replace the piston and the cylinder, and it means that it is necessary to replace a support assembled.
8. Check a condition of all details of a support and replace worn out or damaged. Irrespective of a condition replace all rubber consolidations.
9. Wash out all details in methyl alcohol or pure brake liquid and wipe them. For pro-cleaning of tubes and openings use the compressed air.
10. Dip pistons and new sealing rings of pistons into brake liquid and apply a thin film brake liquid on openings for pistons in a support.
11. Establish sealing rings in openings of cylinders of a support.
12. Establish dustproof covers on pistons so that internal diameter of a cover was included into a piston flute. Being careful and turning, insert the piston into a support.
13. Insert an external edge of a dustproof cover into a support before its fixing. Fix a dustproof cover a bracket.


1. Establish a support on the holder of a back nave and fix bolts, having tightened them the demanded moment.
2. Connect to a support a brake tube and fix it a connecting nut.
3. Establish brake shoes.
4. Remove polyethylene from a jellied mouth of a popolnitelny tank of brake system and pump over the corresponding contour.
5. Establish a wheel and lower the car. Tighten bolts of fastening of a wheel.